国产精品久久久久无码av色戒,大帝av在线一区二区三区,国产肥熟女视频一区二区三区,大陆少妇xxxx做受,被黑人猛躁10次高潮视频

Members of the Texas Instruments

SCOPE E Family of Testability Products

Members of the Texas Instruments

WidebusE Family

State-of-the-Art 3.3-V ABT Design Supports

Mixed-Mode Signal Operation (5-V Input

and Output Voltages With 3.3-V VCC)

Support Unregulated Battery Operation

Down to 2.7 V

UBT E (Universal Bus Transceiver)

Combines D-Type Latches and D-Type

Flip-Flops for Operation in Transparent,

Latched, or Clocked Mode

Bus Hold on Data Inputs Eliminates the

Need for External Pullup/Pulldown

Resistors

B-Port Outputs of ’LVTH182504A Devices

Have Equivalent 25-W Series Resistors, So

No External Resistors Are Required

Compatible With the IEEE Std 1149.1-1990

(JTAG) Test Access Port and

Boundary-Scan Architecture

SCOPE Instruction Set

– IEEE Std 1149.1-1990 Required

Instructions and Optional CLAMP and

HIGHZ

– Parallel-Signature Analysis at Inputs

– Pseudo-Random Pattern Generation

From Outputs

– Sample Inputs/Toggle Outputs

– Binary Count From Outputs

– Device Identification

– Even-Parity Opcodes

Packaged in 64-Pin Plastic Thin Quad Flat

(PM) Packages Using 0.5-mm

Center-to-Center Spacings and 68-Pin

Ceramic Quad Flat (HV) Packages Using

25-mil Center-to-Center Spacings

description

The ’LVTH18504A and ’LVTH182504A scan test devices with 20-bit universal bus transceivers are members

of the Texas Instruments (TI) SCOPE testability integrated-circuit family. This family of devices supports

IEEE Std 1149.1-1990 boundary scan to facilitate testing of complex circuit-board assemblies. Scan access to

the test circuitry is accomplished via the 4-wire test access port (TAP) interface.

Additionally, these devices are designed specifically for low-voltage (3.3-V) VCC operation, but with the

capability to provide a TTL interface to a 5-V system environment.

In the normal mode, these devices are 20-bit universal bus transceivers that combine D-type latches and D-type

flip-flops to allow data flow in transparent, latched, or clocked modes. The test circuitry can be activated by the

TAP to take snapshot samples of the data appearing at the device pins or to perform a self-test on the

boundary-test cells. Activating the TAP in the normal mode does not affect the functional operation of the

SCOPE universal bus transceivers.

Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch-enable (LEAB and LEBA),

clock-enable (CLKENAB and CLKENBA), and clock (CLKAB and CLKBA) inputs. For A-to-B data flow, the

device operates in the transparent mode when LEAB is high. When LEAB is low, the A-bus data is latched while

CLKENAB is high and/or CLKAB is held at a static low or high logic level. Otherwise, if LEAB is low and

CLKENAB is low, A-bus data is stored on a low-to-high transition of CLKAB. When OEAB is low, the B outputs

are active. When OEAB is high, the B outputs are in the high-impedance state. B-to-A data flow is similar to

A-to-B data flow, but uses the OEBA, LEBA, CLKENBA, and CLKBA inputs.

In the test mode, the normal operation of the SCOPE universal bus transceivers is inhibited, and the test circuitry

is enabled to observe and control the I/O boundary of the device. When enabled, the test circuitry performs

boundary-scan test operations according to the protocol described in IEEE Std 1149.1-1990.