国产精品久久久久无码av色戒,大帝av在线一区二区三区,国产肥熟女视频一区二区三区,大陆少妇xxxx做受,被黑人猛躁10次高潮视频

1 Features

? Two-channel bidirectional buffer

? I2C bus and SMBus compatible

? Operating supply voltage range of 2.7V to 5.5V on

B side

? Operating voltage range of 0.9V to 5.5V on A side

? Voltage-level translation from 0.9V to 5.5V and

2.7V to 5.5V

? Active-high repeater-enable input

? Requires no external pullup resistors on lowervoltage

port-A

? Open-drain I2C I/O

? 5.5-V Tolerant I2C and enable input support mixedmode

signal operation

? Lockup-free operation

? Accommodates standard mode and fast mode I2C

devices and multiple controllers

? Supports arbitration and clock stretching across

Repeater

? Powered-off high-impedance I2C bus pins

? Supports 400-kHz fast I2C bus operating speeds

? Available in

– 1.6mm × 1.6mm, 0.4mm height, 0.5mm pitch

QFN package

– 3mm × 3mm Industry standard MSOP package

? Latch-up performance exceeds 100mA Per JESD

78, class II

? ESD protection exceeds JESD 22

– 2000V Human-body model (A114-A)

– 1000V Charged-device model (C101)

2 Applications

? Servers

? Routers (Telecom Switching Equipment)

? Industrial Equipment

? Products with many I2C targets and or long PCB

Traces

3 Description

This TCA9509 integrated circuit is an I2C bus/SMBus Repeater for use in I2C/SMBus systems. It can also

provide bidirectional voltage-level translation (up-translation/down-translation) between low voltages (down to

0.9V) and higher voltages (2.7V to 5.5V) in mixed-mode applications. This device enables I2C and similar bus

systems to be extended, without degradation of performance even during level shifting.

The TCA9509 buffers both the serial data (SDA) and the serial clock (SCL) signals on the I2C bus, thus allowing

400pF bus capacitance on the B-side. This device can also be used to isolate two halves of a bus for voltage

and capacitance.

The TCA9509 has two types of drivers – A-side drivers and B-side drivers. All inputs and B-side I/Os are

overvoltage tolerant to 5.5V. The A-side I/Os are overvoltage tolerant to 5.5V when the device is unpowered

(VCCB and/or VCCA = 0 V).

The bus port B drivers are compliant with SMBus I/O levels, while the A-side uses a current sensing mechanism

to detect the input or output LOW signal which prevents bus lock-up. The A-side uses a 1 mA current source

for pull-up and a 200Ω pull-down driver. This results in a LOW on the A-side accommodating smaller voltage

swings. The output pull-down on the A-side internal buffer LOW is set for approximately 0.2V, while the input

threshold of the internal buffer is set about 50mV lower than that of the output voltage LOW. When the A-side

I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition

from occurring. The output pull-down on the B-side drives a hard LOW and the input level is set at 0.3 of SMBus

or I2C-bus voltage level which enables B side to connect to any other I2C-bus devices or buffer.

The TCA9509 drivers are not enabled unless VCCA is above 0.8V and VCCB is above 2.5V. The enable (EN) pin

can also be used to turn the drivers on and off under system control. Caution should be observed to only change

the state of the EN pin when the bus is idle.