国产精品久久久久无码av色戒,大帝av在线一区二区三区,国产肥熟女视频一区二区三区,大陆少妇xxxx做受,被黑人猛躁10次高潮视频

Members of the Texas Instruments

WidebusE Family

State-of-the-Art Advanced BiCMOS

Technology (ABT) Design for 3.3-V

Operation and Low Static-Power

Dissipation

Support Mixed-Mode Signal Operation

(5-V Input and Output Voltages With

3.3-V VCC)

Support Unregulated Battery Operation

Down to 2.7 V

Typical VOLP (Output Ground Bounce)

< 0.8 V at VCC = 3.3 V, TA = 25°C

Ioff and Power-Up 3-State Support Hot

Insertion

Bus Hold on Data Inputs Eliminates the

Need for External Pullup/Pulldown

Resistors

Distributed VCC and GND Pin Configuration

Minimizes High-Speed Switching Noise

Flow-Through Architecture Optimizes PCB

Layout

Latch-Up Performance Exceeds 500 mA Per

JESD 17

ESD Protection Exceeds 2000 V Per

MIL-STD-883, Method 3015; Exceeds 200 V

Using Machine Model (C = 200 pF, R = 0)

Package Options Include Plastic Shrink

Small-Outline (DL) and Thin Shrink

Small-Outline (DGG) Packages and 380-mil

Fine-Pitch Ceramic Flat (WD) Package

Using 25-mil Center-to-Center Spacings

description

The ’LVTH16652 devices are 16-bit bus transceivers designed for low-voltage (3.3-V) VCC operation, but with

the capability to provide a TTL interface to a 5-V system environment. These devices can be used as two 8-bit

transceivers or one 16-bit transceiver.

Output-enable (OEAB and OEBA) inputs are provided to control the transceiver functions. Select-control (SAB

and SBA) inputs are provided to select whether real-time or stored data is transferred. A low input level selects

real-time data, and a high input level selects stored data. The circuitry used for select control eliminates the

typical decoding glitch that occurs in a multiplexer during the transition between stored and real-time data.

Figure 1 illustrates the four fundamental bus-management functions that can be performed with the

’LVTH16652 devices.

Data on the A or B bus, or both, can be stored in the internal D flip-flops by low-to-high transitions at the

appropriate clock (CLKAB or CLKBA) inputs, regardless of the levels on the select-control or output-enable

inputs. When SAB and SBA are in the real-time transfer mode, it also is possible to store data without using the

internal D-type flip-flops by simultaneously enabling OEAB and OEBA. In this configuration, each output

reinforces its input. When all other data sources to the two sets of bus lines are at high impedance, each set

of bus lines remains at its last level configuration.

When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down.

However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor

and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by

the current-sinking/current-sourcing capability of the driver.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.

These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry

disables the outputs, preventing damaging current backflow through the devices when they are powered down.

The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,

which prevents driver conflict.

The SN54LVTH16652 is characterized for operation over the full military temperature range of –55°C to 125°C.

The SN74LVTH16652 is characterized for operation from –40°C to 85°C.